Fluke 789/773 BU 789 Process Meter and 773 Milliamp Process Meter Bundle Package

Description

FLUKE - 789 AND 773 BUNDLE PACKAGE
Features:
Fluke 789 Process Meter Features
24 V Loop power supply
Very large dual display
Enhanced backlight with 2 brightness settings
1200 Ohm drive capability on mA source
HART mode setting with loop power and a built-in 250 ohm resistor
0% and 100 % buttons to toggle between 4 and 20 mA sourcing for a quick span check
Externally accessible fuses for easy replacement
Infrared-port to process data in FlukeView Forms (V2.1) software
Precision 1000 V, 440 mA True-RMS digital Multimeter
DMM designed to meet 1000 volt IEC 1010 CAT III standards
Frequency measurement to 20 kHz
Min/Max/Average/Hold/Relative modes
Diode Test and Continuity Beeper
Simultaneous mA and % of scale readout
20 mA DC current source / loop calibrator / simulator
Manual Step (100%, 25%, Coarse, Fine) plus Auto Step and Auto Ramp
Externally accessible battery for easy battery changes
Fluke 773 Milliamp Process Clamp Meter
Best in class 0.2% accuracy
0.01 mA resolution and sensitivity
Measure 4 to 20 mA signals without “breaking the loop”
Measure mA signals for PLC and control system analog I/O
Dual backlit display with both mA measurement and percent of 4 to 20 mA span
Measurement Spotlight illuminates hard to see wires in dark enclosures
Detachable clamp with extension cable for measurements in tight locations
Measure 10 to 50 mA signals in older control systems using the 99.9 mA range
Automatically change the 4 to 20 mA output for remote testing
Power saving features, auto-off, backlight timeout extend battery life
Hold function captures and displays changing measurements
Measure 4 to 20 mA signals with in-circuit measurement
Simultaneous mA in-circuit measurement with 24V loop power for powering and testing transmitters
Source 4 to 20 mA signals for testing control system I/O or I/Ps
mA output linear ramp or 25% step output
Automatically change the 4 to 20 mA output for remote testing
DC voltage measurement to verify 24V power supplies or voltage I/O signals
Source DC voltage to test input devices that accept a 1-5V or 0 to 10V signals
Scaled mA output provides a continuous mA signal that corresponds to the 4 to 20 mA signal measured by the mA clamp
Enables milliamp signal logging to a separate logging device without breaking the loop
Output mA signal enables a logging DMM or other device to record the 4- to 20 mA signal without breaking the loop
mA in/out: simultaneously measure the mA signal with the clamp and source a mA signal
Apply a mA input signal to a device and measure its’ 4-20 mA output on devices such as valves or mA isolators
Voltage output linear ramp or 25% step output
Automatically change the voltage output for remote testing
What's In The Box:
Fluke 773 includes:
(4) AA alkaline batteries (installed)
(1) Soft carrying case
(1) TL75 test leads
(1) AC 72 detachable clip
(1) TL 940 mini hook test leads
(1) Instruction sheet
(1) Hanging tool with hook and loop strap
Fluke 789  includes:
(1) AC175 Alligator Clips
(4) AA 1.5 V alkaline battery (installed)
(1) TL71 Safety-Designed Test lead Set
(1) Users Manual
(1) Quick Reference Guide
About TEquipmentSales:
TEquipmentSales is a well-established, US authorized manufacturer / distributor of major brands of test equipment, interactive whiteboards and educational technology products. We take tremendous pride in having built a company with a reputation for quality products, unsurpassed customer service, and competitive prices. These three components not only account for our past and present, but will, unquestionably, determine our future.
Shipping:
Please review the shipping tab for each item for any shipping costs and shipping location restrictions. We do not process shipments on weekends and holidays. Local pick up is not available. We do not accept P.O. BOXES. Please provide a physical address. For more information on our shipping policies, please contact us.
Payment:
Currently all payments must be made directly though PayPal.
Return Policy:
All return requests must be made within 30 days of receipt. Should your item arrive damaged, please contact us within 3 days of receipt. Photos are greatly appreciated! If your item appears defective, a call to the manufacturer may solve your issue. Please consider troubleshooting prior to making a return request.
Customer Service:
Feel free to contact us with any of your customer service needs. Our customer service staff is available Monday through Friday from 7:00 AM - 7:00 PM (EST). We are more than a business; we are a family and we would love to hear from YOU!